黑威联通心水已久，希望哪位大神可以帮忙写一个 model.conf。 大神帮我搞一个黑威的启动盘

主板是华擎的：Z690m-itx/ac

有装好的 debian12 系统，需要提前准备什么都可以。

aby001 发表于 2023-7-14 11:07
usb启动 ，usb不能写错且 优盘口不能插错，
假设是usb启动写得问题，拔下来 多试试其他的口，
正确口系统 ...

搞定了开机，现在4快继续盘，2快M2，2个网卡，内存，独显，这几样搞定了。剩下的是USB和温控，有写USB的经验吗？

viset 发表于 2023-7-14 23:43
先把不必要的参数删除，特别是有地址的，我估计如果错了也会影响启动，可以参考下其他人的

只保留usb启 ...

引导 sata nvme 内存 都搞定了。现在还差USB 跟 温控

先把不必要的参数删除，特别是有地址的，我估计如果错了也会影响启动，可以参考下其他人的

只保留usb启动项和网卡，usb和硬盘都可以先不要，启动项和网卡对了就能启动了，后面的慢慢加

usb的写法，参考这个地址，大神写得很详细  http=s://=271328.=com=/1/ （链接不让发，记得去掉=）
有个ls -al /sys/block/sd*命令很好用

usb启动 ，usb不能写错且 优盘口不能插错，
假设是usb启动写得问题，拔下来 多试试其他的口，
正确口系统会继续走下去，不用关电脑

[System Network 2]
DEV_BUS = B0031:F6
DEV_PORT = 1    这里写0看看
SLOT_NAME=1GbE-2  

换个rms大佬的启动盘试试

model写别写那么多，先写sata硬盘 usb写几个能启动的，然后网卡，然后做工具盘
用的是ljfl的还是 rmt amd大佬的，
laoji的8125启动盘记得没驱动，用rmt大佬的 论坛搜amd

aby001 发表于 2023-7-13 16:35
+-1d.0-[02]----00.0  Intel Corporation NVMe Optane Memory Series
这个是nvme自己写哦

这是我现在的配置，帮我看看是不是写法错了。
[System Enclosure]
VENDOR = QNAP
MODEL = TVS-874
CAP=0x8614db3c
MAX_DISK_NUM = 12
MAX_FAN_NUM = 3
MAX_CPU_FAN_NUM = 1
MAX_TEMP_NUM = 6
MAX_NET_PORT_NUM = 5
INTERNAL_NET_PORT_NUM = 3
NET_PORT_MAPPING = ENHANCE
MAX_PCIE_SLOT = 2
CPU_TEMP_UNIT=SIO:3
SYSTEM_TEMP_UNIT=SIO:1
SIO_DEVICE = IT87
CPLD_DEVICE = MachXO
JTAG_TCK = PCI:A0xFDAE0000:R0x620:BIT0:CMMIO
JTAG_TMS = PCI:A0xFDAE0000:R0x628:BIT0:CMMIO
JTAG_TDI = PCI:A0xFDAE0000:R0x630:BIT0:CMMIO
JTAG_EN = PCI:A0xFDAE0000:R0x610:BIT0:CMMIO
JTAG_TDO = PCI:A0xFDAE0000:R0x618:BIT1:CMMIO
PWR_RECOVERY_UNIT = MMIO:I0xFE001020:B00
PWR_RECOVERY_CMOS_STORE = 0x70,0x61
BOARD_SN_DEVICE = BOOT1:67000000
ETH_MAC_DEVICE = NET
DISK_DRV_TYPE = ATA
DISK_DEFAULT_MAX_LINK_SPEED = PD_SATA_SAS_6G
SYSTEM_DISK_CACHEABLE_BITMAP = 0x7fe
HEAT_PCI_DEVICE = 8086:1528
EUP_STATUS = SIO
SS_MAX_CHANNELS = 80
SS_FREE_CHANNELS = 8
FORCE_ENABLE_SAS_ENC = yes
DISK_SLOT_POWER_CONTROL_SUPPORT = 1
DISK_SLOT_PRESENCE_SUPPORT = 1
[System FAN]
FAN_UNIT = SIO
FAN_1=I2
FAN_2=I3
FAN_3=I4
FAN_LEVEL_0 = 0
FAN_LEVEL_1 = 50
FAN_LEVEL_2 = 70
FAN_LEVEL_3 = 95
FAN_LEVEL_4 = 120
FAN_LEVEL_5 = 160
FAN_LEVEL_6 = 200
FAN_LEVEL_7 = 250
SYSTEM_DISK_MONITOR_BITMAP = 0x7fe
PCIE_SLOT_MONITOR_BITMAP = 0x2
HEAT_SOURCE = SYS, DISK
[CPU FAN]
FAN_UNIT = SIO
FAN_1=I1
FAN_LEVEL_0 = 0
FAN_LEVEL_1 = 50
FAN_LEVEL_2 = 80
FAN_LEVEL_3 = 110
FAN_LEVEL_4 = 140
FAN_LEVEL_5 = 170
FAN_LEVEL_6 = 210
FAN_LEVEL_7 = 250
SYSTEM_DISK_MONITOR_BITMAP = 0x6
HEAT_SOURCE = CPU
[FAN Region]
MAX_REGION_NUM = 2
[System I2C]
DEV_BUS = B0031:F4
DEV_PORT = 0
[System EDID 1]
DEV_BUS = B0002:F0
DEV_PORT = 3
[System IO]
AUDIO_GAIN = 0x1f
AUDIO_LIMITATION = 60
EDID_COUNT=1
VOICE_ALERT_SUPPORT = 0
[System Disk 1]
DISK_FORM_TYPE = PD_FORM_M_2_PCIE
BUS_TYPE = NVME
DISK_DRV_TYPE = M_2
DEV_BUS = B0006:F0
DEV_PORT = 0
SLOT_NAME = M.2 SSD 1
[System Disk 2]
DISK_FORM_TYPE = PD_FORM_M_2_PCIE
BUS_TYPE = NVME
DISK_DRV_TYPE = M_2
DEV_BUS = B0029:F0
DEV_PORT = 0
SLOT_NAME = M.2 SSD 2
[System Disk 3]
DEV_BUS = B0023:F0
DEV_PORT = 0
[System Disk 4]
DEV_BUS = B0023:F0
DEV_PORT = 1
[System Disk 5]
DEV_BUS = B0023:F0
DEV_PORT = 2
[System Disk 6]
DEV_BUS = B0023:F0
DEV_PORT = 1
[System Network 1]
DEV_BUS = B0028:F0
DEV_PORT = 0
SLOT_NAME=2.5GbE-1
[System Network 2]
DEV_BUS = B0031:F6
DEV_PORT = 1
SLOT_NAME=1GbE-2
[Usb Enclosure]
VENDOR = QNAP
MODEL = USB
MAX_PORT_NUM = 8
USB3_PORT_BITMAP = 0x1FE
[Usb Port 1]
DEV_BUS = B00:D28:F0
DEV_PORT = 0
[Usb Port 2]
DEV_BUS = B00:D20:F0
DEV_PORT = 1
[Usb Port 3]
DEV_BUS = B00:D20:F0
DEV_PORT = 2
[Usb Port 4]
DEV_BUS = B00:D20:F0
DEV_PORT = 3
[Usb Port 5]
DEV_BUS = B00:D20:F0
DEV_PORT = 4
[Usb Port 6]
DEV_BUS = B00:D20:F0
DEV_PORT = 5
[Usb Port 7]
DEV_BUS = B00:D20:F0
DEV_PORT = 6
[Boot Enclosure]
VENDOR = QNAP
MODEL = BOOT
MAX_DISK_NUM = 1
DISK_DRV_TYPE = USB
[Boot Disk 1]
DISK_DRV_TYPE = USB
DEV_BUS = B00:D20:F0
DEV_PORT = 7
[Memory I2C 1]
DEV_BUS = B00:D21:F0
DEV_PORT = 0
[System Memory]
MAX_CHANNEL_NUM = 2
MAX_SLOT_NUM = 4
SLOT1_ADDR = 1, 0x50, I1
SLOT2_ADDR = 1, 0x51, I1
SLOT3_ADDR = 2, 0x52, I1
SLOT4_ADDR = 2, 0x53, I1


这个写法，一直卡在这个界面

zml1985 发表于 2023-7-13 22:54
和我的技嘉B660ITX很像， model  你拿去改改应该就直接能用 还有个温控，我是IT8705F的，用附件的可以显示 ...

又搞了一晚上，按照你的配置，我改了一些还是启不来，一样的问题，不知道怎么解决。

和我的技嘉B660ITX很像， model  你拿去改改应该就直接能用 还有个温控，我是IT8705F的，用附件的可以显示，但是没法控制，是BIOS控制